Technology
Sport brake systems
Always safely on the way

Always safe on the road with MTM sport brake systems
The standard brake system is developed and tuned by the manufacturer for use in the respective vehicle. Because of the many different vehicle requirements (braking performance, service life, wear, comfort, cost, weight, noise, etc.), it represents the best possible compromise between the individual development factors. By changing the weighting of these requirements, the system can be optimised in favour of braking performance, although this means accepting losses in other areas (e.g. comfort, wear, noise behaviour).
The MTM sport brake systems offer improved components compared with the standard equipment, including modified floating or multi-piston fixed calipers, larger brake discs, larger brake pads and braided stainless-steel brake lines. These optimise the braking performance and safety of your vehicle.
Brake calipers
Depending on the vehicle category and installation position (front axle/rear axle), the brake calipers of the MTM sport brake systems are designed either as floating calipers or as fixed calipers. Floating calipers are mounted so that they can slide and offer greater braking comfort. They are particularly advantageous where space is limited and are often used on lighter vehicles or on rear axles.
For large or high-performance vehicles such as the Audi RS3, RS4 and RS5, fixed calipers are preferred, especially on the front axle. They offer high inherent rigidity and, thanks to their multi-piston design, ensure that the brake pads are pressed evenly against the discs.
Brake discs
Larger brake discs, as used in the MTM sport brake systems for models such as the Audi RS6, RS7 and RS Q8, have a higher heat capacity and improve the stability of the braking performance (fade). Most MTM brake discs have a complex ventilation system of cooling fins and holes to optimise heat dissipation.
Brake pads
The “Comfort” brake pads are matched to the material of the brake discs and offer a favourable friction pairing for everyday road use. Many pads are fitted with compensating weights to reduce squealing. For sporty use or racing, MTM also offers “Pro” pads, which were developed specially for high temperatures and optimum deceleration values.
Brake hoses
The MTM braided stainless-steel brake lines are Teflon hoses sheathed in stainless steel, which absorb less brake fluid and thus improve the pressure point. They are protected against chafing and stone chips. When installing, make sure that the brake hoses do not touch any parts at full steering lock, to avoid pressure loss.
Installation space
MTM sport brake systems developed for top Audi models such as the RS Q3, RS Q5 and TT RS generally need more installation space. It is important that there is sufficient clearance to all adjacent parts. Standard wheel sizes are often not sufficient, so wheel spacers may be necessary.
Use
New brake discs and pads must be run in gently to achieve optimum deceleration and heat transfer. This bedding-in process takes about 500-1000 km. After heavy use of the brakes, the vehicle should not be parked with hot brake discs, to ensure even cooling and minimise stress.
Maintenance and care
The brake system should be checked and cleaned regularly, especially in winter. Brake dust must be removed to preserve the ventilation system of the discs and avoid thermal overload.
Brake fluid
The brake fluid recommended by the vehicle manufacturer can also be used with MTM sport brake systems. Under heavy use of the brake system, the brake fluid should be checked more often. Special brake fluids with higher boiling points are expedient but must be checked and renewed more frequently.
Wear
The wear of the brake system depends mainly on driving style. Sport brake systems have design limits, and improper use can lead to overload and damage.
Approval
After a change to the brake system, an acceptance test of the modification must be carried out and confirmed. Most MTM sport brake systems have a parts certificate, which allows an entry in the vehicle documents. Some special brake systems require an individual inspection by an approved inspector.
Safety information
All work on the brake system must be carried out by qualified personnel. Damaged brake parts must be replaced immediately. MTM’s warranty does not cover damage caused by improper installation, overload or inadequate maintenance.
Warranty
MTM sport brake systems have load limits. Damage or defects caused by improper installation, defects already present on the vehicle, overload or inadequate maintenance are excluded from the warranty. Wear parts are generally excluded from the warranty.
We will be happy to provide further technical information on the MTM sport brake system that suits your vehicle.